The gear selector is typically found on the center console of your Cadillac. To confirm that the transmission is in neutral, start by locating the gear selector. Shifting your Cadillac into neutral when you have a dead battery is a simple process that can be done manually. Remember to exercise caution and follow the instructions provided in your car’s manual. This will enable you to manually shift the vehicle into neutral, allowing for easier movement during towing or pushing. Insert the tool into the shift override slot and apply gentle pressure while turning it. Once located, you will need appropriate tools, such as a screwdriver or a small key, to access it. It is usually found near the gear shift lever or the center console. Firstly, locate this feature in your vehicle. To put your Cadillac in neutral with a dead battery, you can make use of the shift override feature. By following these steps and taking the necessary precautions, you will be well-prepared to put your Cadillac in neutral with a dead battery. It’s also advisable to wear gloves and eye protection to protect yourself during the process. Ensure that the Cadillac is parked on a level surface and engage the emergency brake to prevent any accidental movement. Safety precautions should also be taken into account before proceeding with the manual shift. It’s important to have a reliable and properly charged battery available to provide power to the Cadillac once it is in neutral. Start by assembling the necessary tools, including a socket wrench and a set of jumper cables. Gathering essential tools is the first step in preparing to put your Cadillac in neutral with a dead battery. Remember to exercise caution and follow any additional safety procedures recommended by your vehicle’s manufacturer. Once you have successfully shifted your Cadillac into neutral, you can then safely move or tow it without the need for engine power. It’s important to note that the exact process may vary slightly depending on the specific Cadillac model you have. Pressing or pulling this button or tab will enable you to shift the gearshift lever into neutral. Once you have located the gearshift lever, look for a small button or tab located either on the side or bottom of the knob. In most Cadillac models, the gearshift lever is a round knob positioned between the driver and front passenger seats. To begin, locate the gearshift lever in the center console of your vehicle. Familiarizing yourself with your Cadillac’s gearshift mechanism is the first step towards putting it in neutral. Recognizing the necessity for manual shifting when faced with a dead battery in your Cadillac is crucial. How To Put Cadillac In Neutral With Dead Battery Then press down on the rear of the trim plate to engage the rear retaining tabs.ĩ. Install the shift control trim plate by inserting the front retaining tabs to the console. Refer to Console Replacement - Front Floor in Instrument Panel, Gages, and ConsoleĨ. Rotate each lamp socket one quarter turn to lock in place.ħ. Install the shift indicator lamp sockets (1 and 2) to the shift indicator. Press down on the rear of the shift indicator to engage the retaining tabs (3).Ħ. Align the rear retaining tabs (3) with the sides of the shift control assembly.ĥ. Press down on the front of the shift indicator to engage the retaining tabs (1).Ĥ. Align the front retaining tabs (1) with the holes in the shift control assembly.ģ. Lower the shift indicator (2) over the shift control shaft.Ģ. Remove the shift indicator (2) from the shift control assembly.ġ. Carefully lift upward on the front of the shift indicator (2) in order to release the front retaining tabs (1)Ĩ. Carefully spread the retaining tabs (3) enough to lift the back of the shift indicator (2) up past the retaining tabs (3).ħ. Remove the shift indicator lamp sockets (1 and 2) from the shift indicator by rotating the lamp sockets one quarter turn.Ħ. Refer to Console Replacement - Front Floor in Instrument Panel, Gages, and Consoleĥ. Disconnect the electrical connectors from the shift control trim plate.Ĥ. Remove the shift control trim plate by lifting the rear of the trim plate up then pull the plate rearward in order to disengage the front retaining tabs.ģ.

Cadillac ats manual shift knob removal